Saab 9-3 Key Replacement Tools To Facilitate Your Daily Life

How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners must follow a set of special steps to install an additional ignition key. It requires dealer assistance using a handheld computer dubbed Tech-2. Then a new key as well as transponder must be purchased and then programmed into the car.

It is a good idea to rotate your keys so that one does not wear out faster than the other. This will keep your keys in top condition.

Replacement Case

The new key fobs are not like the old Saab keys. They're equipped with electronic devices which make it hard to copy. This has made stealing car keys considerably more difficult than it was years ago. It also makes it more expensive to replace lost keys.

Every owner of a Saab 9-3 should have at minimum two working keys. If one is lost it costs a lot of money to replace it in the car, as it requires replacing the CIM module and programming the locking cylinders. Dealers charge between $100-$200 for this.

There are some ways around these high cost. Some parts providers can look up the code from an extra key (usually the same one that opens the doors and turns off the ignition) and cut a new metal key blade at only a fraction of the dealer's cost. The key must be the exact same as the original in order for it to function in your vehicle.

Follow these steps to replace the case. You'll need a flathead screwdriver as well as some patience. With the screwdriver, pry apart the plastic, and then take off the emergency key. After the case is open, remove all electronics and place them into your new case. Insert the correct key and badge inside the case.

Replacement Battery

The replacement battery for the saab key code 9-3 is a low-cost part that can be replaced easily and quickly. This DIY video from YouTube user Cyclone Cyd explains How To Program Saab 9-3 Key Fob - Bitetheass.Com, to replace the battery of the remote key fob in only four steps. This tutorial should work for any modern saab key fob, though the process may vary slightly.

The button is normally located just below the saab key programmer logo on the back of the fob. It is usually located next to the Saab logo on the back of the fob. Next take the flathead screwdriver to insert into the small hole of this button. This will be enough to allow you to open the case of the fob so that you can replace the battery.

Once you have installed the CR1632 batteries, you can restore the remote key fob. You can then program it into your car. The whole process should not exceed an hour. This is a very easy procedure that doesn't require special tools.

The process is more complicated in the event that you lose your key, but it is possible. The dealer will first need to read the VIN of the vehicle and order a replacement TWICE module and key blade with the correct unique code. Then, they'll be required to cut the replacement key and then program it with an innovative software tool called MDI.

Key Replacement Fob

The key fob contains a battery that is used to lock and unlock your car. The batteries last for a certain time that is a long time, and they eventually die. This is a problem that happens to all cars and the good thing is that you can replace the batteries in many key fobs without having to replace the whole case. Amazon sells replacement fobs with all the electronics installed. You can simply open the case and replace the batteries. It is important to remember that you will need to take out the emergency key first, and you can do this by inserting the screwdriver of a small flathead into the slot located in the middle of the case. The case will split as you work the screwdriver all around it.

If you're looking to replace your keys, be sure to have an extra set on hand. This will save you a significant amount of money. If you have an additional key, you can request the dealer to cut the key and program it for your car. This is much less expensive than purchasing a brand new key fob.

It is possible to add a second key to your car if you don't already have one, but it requires a great deal of research and work. It costs a few hundred dollars to get an additional car key. The computer in the vehicle must also be programmed. This can be accomplished by a professional, however it's a costly option for the majority of owners.

Replacement Ignition

Contrary to earlier Saab automobiles, the new SAAB 9-3 models use an upgraded alarm system that is built around a coded key. This means that in the event that you lose your only functioning key, getting an additional one could be extremely expensive as the car has to have a unique computer module installed and it also must be specially programmed to accept a new key. The majority of locksmiths aren't able to do this and even dealers will charge hundreds of dollars just to program the new key!

Dealers will charge you a high price to replace your car computer (also called the CIM or SAAB twice) in the event that you lose your only working key. We can reprogramme the existing EEPROM inside your car's computer so that it is ready to accept an additional key. This will save you more than 50% off the cost you would pay an auto dealer.

If you've been a long-time owner of a 03-11 saab key programmer 9-3, then you probably realize that the ignition key isn't all that robust. If your ignition key isn't working correctly, you should look into replacing it. They can become sticky and the buttons have been known to fall off. It's not as difficult as you think to replace the ignition key. With the right tools, it is able to be done quickly.